Page 2 of 3 FirstFirst 123 LastLast
Results 16 to 30 of 36

Thread: our front fender idea

  1. #16
    Doesnt look like this supernova's Avatar
    Join Date
    May 2002
    Location
    baton rouge, la
    Posts
    6,558
    it all sounds like a terrible idea to cover ugly rims


    vortec owner for the love of god down size that fucking sig, its been mentioned in every fucking thread you have posted in, someone even downsized them for you and reposted them and you still refuse

  2. #17
    Senior Member bigjsp's Avatar
    Join Date
    Nov 2002
    Location
    Columbus, OH
    Posts
    12,665
    Quote Originally Posted by theKILLSHOT! View Post
    the back is the easiest part
    What is the plan to use some "wideside" flairs similar to what I am running on the back of my limo truck?

    Might not be a bad approach for the front too as it would look symetrical, not change any structure since it bolts on.

  3. #18
    will work for food! phatfarmer2's Avatar
    Join Date
    Dec 2003
    Location
    North NJ
    Posts
    7,295
    Fender flares and moving the cold air intake lower or behind the grille. Call it done.
    Grounded 4 Life
    "continuing where the factory left off"

    Street Source page

    Projects i've done

    V8 Love
    Pneumatic Love

  4. #19
    BANG! BANG! VROOOOM! theKILLSHOT!'s Avatar
    Join Date
    Jun 2010
    Location
    elsberry/st.louis missouri
    Posts
    246
    the idea for the rear is to use bed sides and weld them to the rear of the truck and have them taper in twards the doors leave her taillight shavers and run the exhaust up threw the bed sides taillight openings after they are restyled and her fuel filler is in her cargo floor and yes I know the front bumper will need to be extended and we may end up using a fullsize bumper
    True memories are not set in stone
    Their sculpted from steel and covered with blo0d
    (mayhem)

  5. #20
    5.7L VORTEC 350 blazin4low's Avatar
    Join Date
    Aug 2002
    Location
    Jax,FL
    Posts
    2,615
    it will look something like this


    if you had a typhoon or syclone it would be easyer
    Last edited by blazin4low; 01-16-2011 at 08:42 PM.
    http://i158.photobucket.com/albums/t114/VortecBlazer/sidredo.jpg
    Tuned by Bland Tuning
    Transmission built by Transbuilderguy on FSC!
    Marine Intake swap by me

  6. #21
    Upright Member smsmith36's Avatar
    Join Date
    Oct 2004
    Location
    York, PA
    Posts
    2,079
    If this said "Killshot" on the side it would be perfect.


    Genius by birth, Slacker by choice.

  7. #22
    BANG! BANG! VROOOOM! theKILLSHOT!'s Avatar
    Join Date
    Jun 2010
    Location
    elsberry/st.louis missouri
    Posts
    246
    yeah its my gfs truck not mine and hers is just blue and thare is no "artwork" on hers and I'm not doing any fiberglass on it I'm an all metal kind of guy
    True memories are not set in stone
    Their sculpted from steel and covered with blo0d
    (mayhem)

  8. #23
    Senior Member bigjsp's Avatar
    Join Date
    Nov 2002
    Location
    Columbus, OH
    Posts
    12,665
    That actually looks better than I WAS SUSPECTING. I was thinking about running boards or some trucksterosa fins to bridge the Fender bulges through the door area.

    I'd leave gills on the rear fenders to match the front. Give it a baja meets shark feel

  9. #24
    5.7L VORTEC 350 blazin4low's Avatar
    Join Date
    Aug 2002
    Location
    Jax,FL
    Posts
    2,615
    take a look at this guys fender flaring work on an old volvo
    http://www.pro-touring.com/showthrea...ot-Volvo/page2

    it might be a good way to flare your girls
    http://i158.photobucket.com/albums/t114/VortecBlazer/sidredo.jpg
    Tuned by Bland Tuning
    Transmission built by Transbuilderguy on FSC!
    Marine Intake swap by me

  10. #25
    BANG! BANG! VROOOOM! theKILLSHOT!'s Avatar
    Join Date
    Jun 2010
    Location
    elsberry/st.louis missouri
    Posts
    246
    the rear will be similar but she has a 2 door 2 wheel drive so were going to be using the style line under the rear windows to add the bed sides on and they will be more of a wedge shape with the rear about 6-8 inches wider maybe a little more and the tail light openings will be restyled (the the rear of the opening will be moved back) and thare will be no openings in the front of the fenders.... i braught it up to her cause i thaught it would be a good idea for cooling the breaks she said no
    True memories are not set in stone
    Their sculpted from steel and covered with blo0d
    (mayhem)

  11. #26
    houston-streets.com vortec owner's Avatar
    Join Date
    Mar 2009
    Location
    houston
    Posts
    211
    Quote Originally Posted by supernova View Post
    it all sounds like a terrible idea to cover ugly rims


    vortec owner for the love of god down size that fucking sig, its been mentioned in every fucking thread you have posted in, someone even downsized them for you and reposted them and you still refuse
    i would cuz i didnt think it would be that either but i havent seen anyone down size it for me but if they did have them send it to my email and i will use it houston2kkerarri@yahoo.com plz thanks

  12. #27
    Banned
    Join Date
    Nov 2002
    Location
    Lyndon, Kansas
    Posts
    7,511
    Quote Originally Posted by supernova View Post
    vortec owner for the love of god down size that fucking sig, its been mentioned in every fucking thread you have posted in, someone even downsized them for you and reposted them and you still refuse

    This and,

    *Vote to ban.


    Quote Originally Posted by smsmith36 View Post
    I think you two were made for each other.

    HAHAHA

    Quote Originally Posted by blazin4low View Post
    it will look something like this
    HAHAHAHA



    This all sounds like a horrible idea. This is def a moderate skill level job to widen the fenders and graft all this stuff on, i dont know what kind of metal work skills you have but this is not going to be easy to pull off if you want it to look GOOD and not like someones crazy ex shot it up and slapped bondo on it to cover it up.


    89' S10 blazer 4wd: 355, 650 dp, rpm intake, comp 282 roller cam, modified vortecs, T56 Six speed, 8.8 ls rear, headers, x-pipe, spintech pro street mufflers, and......AC

    Blazer burnout video - http://www.youtube.com/watch?v=sP7iLypoDI4

  13. #28
    Banned
    Join Date
    Nov 2002
    Location
    Lyndon, Kansas
    Posts
    7,511
    Quote Originally Posted by vortec owner View Post
    i would cuz i didnt think it would be that either but i havent seen anyone down size it for me but if they did have them send it to my email and i will use it houston2kkerarri@yahoo.com plz thanks


    Really? Cuz i could have sworn the pictures right under your post on post number 93 look resized. but maybe its just me.


    http://www.blazinlow.com/forum/showt...t=75740&page=7


    89' S10 blazer 4wd: 355, 650 dp, rpm intake, comp 282 roller cam, modified vortecs, T56 Six speed, 8.8 ls rear, headers, x-pipe, spintech pro street mufflers, and......AC

    Blazer burnout video - http://www.youtube.com/watch?v=sP7iLypoDI4

  14. #29
    houston-streets.com vortec owner's Avatar
    Join Date
    Mar 2009
    Location
    houston
    Posts
    211
    Quote Originally Posted by Superbee View Post
    Really? Cuz i could have sworn the pictures right under your post on post number 93 look resized. but maybe its just me.


    http://www.blazinlow.com/forum/showt...t=75740&page=7
    thanx for showing me i will use the resized pics plus i'm hardly ever on here since i moved out of my parents house no comp at my place but thanks guys for the resize didnt know i could resize with my photobucket

  15. #30
    5.7L VORTEC 350 blazin4low's Avatar
    Join Date
    Aug 2002
    Location
    Jax,FL
    Posts
    2,615
    I remember the resize............because I did it
    http://www.blazinlow.com/forum/showp...5&postcount=93

    PWNED
    http://i158.photobucket.com/albums/t114/VortecBlazer/sidredo.jpg
    Tuned by Bland Tuning
    Transmission built by Transbuilderguy on FSC!
    Marine Intake swap by me

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •